Momentum Modbus Plus 170 PNT Series Guia do Utilizador Página 295
- Página / 376
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
Configuring an M1 CPU with Concept
870USE10110 July 2004 295
Configuring Ethernet I/O for Momentum Components (Using Concept)
Overview Once the Ethernet port address parameters have been set, you may assign
parameters for I/O scanning.
Health Block Specify the starting register of the register block which will contain the health bits for
each of the IO Scanner transactions that you intend to configure.
If you designate a 3x register, the health bits for 64 transactions (maximum) will be
stored in 4 contiguous registers starting at the address you specify
If you designate a 1x register, the health bits will be stored in 64 contiguous discrete
registers.
A health bit is set only if the associated transaction has completed successfully
within the last health timeout period for that transaction (see below). When the PLC
is started, all configured transactions have their respective health bit preset to 1. If
the transaction subsequently fails, then the health bit is cleared after the
programmed health timeout period has expired.
IP Address Type the IP address of the slave module in the IP address column. This address will
be stored in a pull-down menu, so that you may use it in another row by clicking on
the down arrow and selecting it, as shown:
Unit ID If the slave module is an I/O device attached to the specified slave module, use the
Unit ID column to indicate the device number.
Health Timeout Use this column to specify the length of time in ms to try the transaction before timing
out. Valid values are 0 ... 65,000 ms (1 min). To avoid timing out, specify 0.
Ethernet Configuration:
I/O Scanner Configuration:
Specify IP Address
Use Bootp Server
Disable Ethernet
Internet Address:
Gateway:
Subnet Mask:
Master Module (Slot):
Health Block (1X/3X):
Diagnostic Block (3X/4X):
171 CCC 980 20-984
0.0.0.0
0.0.0.0
255.255.255.0
Copy Cut Paste Import
Delete Fill Down Export
Slave IP Address
Unit ID
Health
Timeout
(ms)
Rep
Rate
(ms)
Link Type
Read Ref
Master
Read Ref
Slave
Read
Length
Last Value
(Input)
Write Ref
Master
Write Ref
Slave
Write
Length
Description
1
2
3
4
5
6
7
8
9
10
11
OK Cancel Help
Go
Ethernet / I/O Scanner
300001
-300004
192.168.138.50
192.168.138.55
0
0
0
0
0
0
Normal
Normal
400008
400020
400050
400060
1
5
Hold Las
Hold Las
400001
400050
400040
400055
10
1
- Momentum M1 Processor 1
- Adapter and Option Adapter 1
- User Guide 1
- Table of Contents 3
- 4 870USE10110 July 2004 4
- 870USE10110 July 2004 5 5
- 6 870USE10110 July 2004 6
- 870USE10110 July 2004 7 7
- 8 870USE10110 July 2004 8
- 870USE10110 July 2004 9 9
- 10 870USE10110 July 2004 10
- Safety Information 11
- About the Book 13
- Getting Started 16
- Overview of Momentum M1 17
- Processor Adapters 17
- Label Description 19
- 1 Standard port connector 19
- 3 LED indicators 19
- 870USE10110 July 2004 21 21
- Memory Size and 22
- Clock Speed 22
- Input and Output 23
- References 23
- 1 Modbus Port 1 connector 26
- 2 LED indicators 26
- 870USE10110 July 2004 27 27
- 870USE10110 July 2004 31 31
- 2 I/0Bus port connector 32
- 870USE10110 July 2004 33 33
- 870USE10110 July 2004 37 37
- 2 Modbus Port 2 connector 38
- 870USE10110 July 2004 39 39
- 870USE10110 July 2004 43 43
- 1 Ethernet port connector 44
- 2 I/OBus port connector 44
- 3LED indicators 44
- 870USE10110 July 2004 45 45
- 870USE10110 July 2004 47 47
- 870USE10110 July 2004 51 51
- 870USE10110 July 2004 55 55
- 870USE10110 July 2004 57 57
- 870USE10110 July 2004 59 59
- 870USE10110 July 2004 61 61
- Overview of 63
- Momentum Option Adapters 63
- 870USE10110 July 2004 67 67
- 172 JNN 210 32 68
- Serial Option 68
- Adapter 68
- Specifications 68
- 1 LED indicator 70
- 2 Battery compartment door 70
- 870USE10110 July 2004 71 71
- 172 PNN 210 22 72
- 870USE10110 July 2004 73 73
- (A Momentum Component) 74
- 870USE10110 July 2004 75 75
- 870USE10110 July 2004 77 77
- 870USE10110 July 2004 79 79
- Assembling 81
- 870USE10110 July 2004 83 83
- Procedure: 84
- Assembling an 84
- Adapter and an 84
- I/O Base 84
- 870USE10110 July 2004 85 85
- Removing an 87
- Adapter from an 87
- 870USE10110 July 2004 89 89
- 870USE10110 July 2004 91 91
- I/O base 93
- 2 Lift off the adapter 95
- Installation Guidelines 96
- 870USE10110 July 2004 97 97
- 3.4 Labeling the M1 CPU 99
- 870USE10110 July 2004 100
- Communication Ports on 101
- Momentum Components 101
- Communication Ports 102
- Using the Modbus Ports for 103
- 4.1 Modbus Port 1 104
- Using the Modbus Ports 105
- 4.2 Modbus Port 2 109
- Interconnect 119
- Components 122
- Modbus RS485 126
- Connector T 126
- (RJ45 Base) 126
- Using the Modbus Plus Ports 130
- Standard Cabling Schemes 132
- Cluster Mode Cabling Schemes 134
- Cluster 136
- Scheme #1 136
- Scheme #2 137
- Cable Between 139
- Clusters 139
- Terminating 143
- Resistor Plugs 143
- Using the Ethernet Port on 149
- Ethernet Port 150
- Using the Ethernet Port 151
- Transmission 162
- Transmission errors table 162
- Using the I/O Bus Port for 163
- Networks Momentum 163
- Using the I/O Bus Port 164
- Modsoft and Momentum 171
- Configuring an M1 CPU with 173
- Overview 174
- 870USE10110 July 2004 175 175
- Magnum 176
- Step Action 176
- 870USE10110 July 2004 177 177
- 2 Push <Enter> 178
- 870USE10110 July 2004 179 179
- Defaults for an 180
- 18.0 Adapter 180
- 870USE10110 July 2004 181 181
- 870USE10110 July 2004 183 183
- 870USE10110 July 2004 185 185
- Adapters 187
- Specials : 189
- Battery Coil 001536 189
- Timer Register 4 189
- 870USE10110 July 2004 191 191
- Port Parameters with Modsoft 193
- Should Not Be Changed 195
- 870USE10110 July 2004 197 197
- Using Modsoft 198
- Components Using Modsoft 199
- Adapters with Modsoft 203
- 870USE10110 July 2004 205 205
- At a Glance 207
- 870USE10110 July 2004 211 211
- 870USE10110 July 2004 213 213
- Configuring a Modbus Plus 215
- 10.1 Getting Started 216
- Modsoft) 220
- 3 Push <Enter> 222
- 870USE10110 July 2004 223 223
- 870USE10110 July 2004 227 227
- 870USE10110 July 2004 229 229
- 870USE10110 July 2004 231 231
- Completed 233
- Screen: Node 5 233
- (Using Modsoft) 235
- 870USE10110 July 2004 237 237
- 870USE10110 July 2004 239 239
- Defining the 240
- Global Inputs 240
- 870USE10110 July 2004 241 241
- Push <Enter> 242
- Defining Global 244
- 870USE10110 July 2004 245 245
- 870USE10110 July 2004 247 247
- 870USE10110 July 2004 249 249
- Saving to Flash 252
- Concept and Momentum 255
- 870USE10110 July 2004 259 259
- 870USE10110 July 2004 261 261
- 870USE10110 July 2004 263 263
- 870USE10110 July 2004 265 265
- 870USE10110 July 2004 267 267
- Default 144 words 268
- Minimum 4 words 268
- 870USE10110 July 2004 269 269
- 870USE10110 July 2004 271 271
- 870USE10110 July 2004 275 275
- 870USE10110 July 2004 277 277
- 870USE10110 July 2004 279 279
- 870USE10110 July 2004 281 281
- Using Concept 282
- Changing Mode and Data Bits 283
- 870USE10110 July 2004 285 285
- Changing the Modbus Address 287
- I/O Scanning 289
- Subnet Mask: 291
- Master Module (Slot): 291
- Health Block (1X/3X): 291
- (Using Concept) 292
- Components (Using Concept) 293
- Diagnostic Block (3X/4X): 295
- 171 CCC 980 20-984 295
- As shown below: 297
- 870USE10110 July 2004 299 299
- Editing the Local 301
- I/O map 301
- 2 Click on the Insert button 305
- Drop dialog appears 306
- 870USE10110 July 2004 307 307
- 870USE10110 July 2004 309 309
- 14.1 Getting Started 312
- Accessing the 313
- 870USE10110 July 2004 315 315
- Option Effect 316
- Devices on the Network 318
- 870USE10110 July 2004 321 321
- Cop dialog box 322
- 5 Click <OK> 332
- 870USE10110 July 2004 333 333
- Global Outputs 336
- Saving to Flash in Concept 337
- ProWORX32 and Momentum 341
- Configuring an M1 with 343
- ProWORX32 343
- File Edit View Window Help 344
- ProWORX 32 - [RIO_test] 344
- Modbus Plus Gateway TCP/IP 345
- 870USE10110 July 2004 347 347
- Hardware Clock 348
- Registers 348
- 870USE10110 July 2004 349 349
- Selecting the 350
- 870USE10110 July 2004 351 351
- 870USE10110 July 2004 353 353
- Appendices 357
- Ladder Logic Elements and 359
- Instructions 359
- Ladder Logic 360
- Standard Ladder 361
- A Special STAT Instruction 363
- Words Description 364
- 4 Not used 364
- 870USE10110 July 2004 365 365
- 16151413121110987654321 366
- 1 = ATI healthy 366
- 0 = ATI Not Healthy 366
- Error Codes 367
- Battery Life Information for 369
- Alkaline Batteries 369
- 870USE10110 July 2004 371 371
- Numerics 373
- 870USE10110 July 2004 375 375
© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.212 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais